303 Plus Manual

File Name:303 Plus Manual.pdf
Size:3035 KB
Type:PDF, ePub, eBook, fb2, mobi, txt, doc, rtf, djvu
Category:Book
Uploaded17 May 2020, 20:16 PM
InterfaceEnglish
Rating4.6/5 from 587 votes
StatusAVAILABLE
Last checked19 Minutes ago!

303 Plus Manual

Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. A photo detector converts transmitted light energy into electrical signals, which are amplified and interpreted. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. Do Not Operate Without Covers Do not operate this instrument with covers and panels removed. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. Interface: “DB- 9P” is configured for data terminal equipment (“D” connector with 9 male pin contacts.) Pin 1 is ground, Pin 2 is the transmit data output. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. If so, results less than what cutoff should be labeled as negative? 12. Will you be running partial strips. If so, you may want to assign an END location. Stat Fax 303 Plus Operator’s Manual Rev. J. If a test is stored in the test menu, the strip type will also be saved. J Awareness Technology, Inc. The user may select Correction factor and equivocal range options. These adjust the cutoff value to determine cutoff points for interpretation of subsequent specimens. Stat Fax 303 Plus Operator’s Manual Rev. J. Your choices will be printed, and the operating mode will resume. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. If your test is stored, the locations and acceptance criteria of the controls entered will also be stored for later recall. Stat Fax 303 Plus Operator’s Manual Rev. J.http://mebel-kxm.ru/userfiles/coast-guard-ceremonial-manual.xml

Ensure that these holes are not blocked or obscured by 12-Way Carrier 8-Way Carrier markings on (STANDARD) (OPTIONAL) the end of strip tabs. J Awareness Technology, Inc. While the strip is being automatically positioned for reading, the display will indicate “Positioning Strp”. Stat Fax 303 Plus Operator’s Manual Rev. J. Enter the minimum cutoff value. J Awareness Technology, Inc. L - indicates that the individual control was lower than the limit entered. Stat Fax 303 Plus Operator’s Manual Rev. J. The instrument will prompt “NEG Load the first strip into the right-most carrier position and press ENTER. While the strip is being automatically positioned for reading, the display will indicate “Positioning Strp”. Stat Fax 303 Plus Operator’s Manual Rev. J. The display then prompts for unit selection. J Awareness Technology, Inc. To continue reading in the Regression mode, load the next strip and press the ENTER key. Press CLEAR twice to cancel the mode. Stat Fax 303 Plus Operator’s Manual Rev. J. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. Except for the differences mentioned above, please follow the procedures for running the Point- to-Point mode to proceed in this mode. Stat Fax 303 Plus Operator’s Manual Rev. J. Remember to update your log. The instrument will record the date and time that each test was stored or last modified. J Awareness Technology, Inc. Enter the value that should be subtracted from the observed blank absorbance. Stat Fax 303 Plus Operator’s Manual Rev. J. If this happens, simply allow the keyboard to dry before resuming operation. Such a spill does not present a hazard, but may cause temporary malfunction of the keys. J Awareness Technology, Inc. Refer to the operating instructions for each mode regarding correct placement of the blank and calibrator materials. Stat Fax 303 Plus Operator’s Manual Rev. J. Support is available to help you solve any technical problem or question with this instrument.http://brod-plovdiv.com/images/coast-guard-colors-and-coatings-manual.xml

Please call, fax, or write your dealer for immediate attention. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. J Awareness Technology, Inc. Stat Fax 303 Plus Operator’s Manual Rev. J. Stat Fax 303 Plus Operator’s Manual Rev. J Awareness Technology, Inc. Use our model number locator tool, or download our engine numbering system fact sheet. It will be in the format XXXXXX-XX. If you only have a 5 digit number, add a 0 (zero) before the 5 digits. It will be in the format XXXXXX-XXXX.Please refresh and try again. If you truly love music, this single device will open up new dimensions of listening enjoyment you never dreamed possible. Simply tap and flick on the intuitively designed screen, and easily operate all of your MusicCast devices, as well as the R-N303D. Feel the very breath of the vocals, bask in the airy atmosphere of a concert hall — and experience all of the performance as never before. It can stream digital music content from your smartphone, PC or NAS to other MusicCast devices in your home. It can also share the music from external devices such as a CD player or TV connected to the R-N303D.The audio stays in the digital domain, giving you pure, pristine, dynamic sound for all your entertainment sources, from sports and other programmes to movies and concerts. We each have a similar goal to persistently break the limits, and strive for innovation. In Win and MSI unite for the first time to design the In Win 303-MSI Dragon Edition. The simple aesthetic is slightly altered, but preserved enough to bring forth the stunning Dragon Edition to life. Its aesthetic design embodies the spirit of innovation. Even the 3mm tempered glass side panel will flash a fantastic array of colors!

Mission accomplished since it has perfected a tool-less design by being able to remove the beautiful 3mm tempered glass side panel by just pressing the handle. It’s conveniently located on the bottom, and removing dust has never been easier. The cool air intake from the bottom creates efficient air flow for quick heat dissipation. The specialized GPU holder can provide extra support to graphics cards. Yet another detail In Win oversees when manufacturing to make PC building much easier. By clicking any link on this page you are giving your consent to our Cookies Policy and Privacy Policy. Are you sure to remove this product? By continuing to browse or use this site, you are agreeing to our use of cookies.Please share your ZIP Code to find a nearby Best Buy to try out your next phone. Please share your ZIP Code to find a nearby Best Buy location Navigate to Settings,. The following. This video will outline how to use preset. Ask a question or start a new topic to get help and advice from our loyal Samsung community. Or Text HELP to 62913 Please contact us via Live Chat for a faster response.Samsung pays for Premium Care during this period. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Sp 303 Manual. To get started finding Sp 303 Manual, you are right to find our website which has a comprehensive collection of manuals listed. Our library is the biggest of these that have literally hundreds of thousands of different products represented. I get my most wanted eBook Many thanks If there is a survey it only takes 5 minutes, try any survey which works for you. You must have JavaScript enabled in your browser to utilize the functionality of this website. We've got you covered. Please select the product you are looking for to begin downloading. Instruction books are available in English, Espanol, and Francais.

The STM32L5 is now in full production and all its ecosystem is available including hardware kits, software tools, firmware and all documentations of course. This is our first STM32 based on Cortex-M33 and its Trustzone and using specific ST security implementation - watch the video to find out more!This video shows how to enable TrustZone on STM32L562E-DK discovery using STM32CubeProgrammer and create, compile and debug or run a new project with STM32CubeIDE. It also shows how to open an example project delivered in STM32CubeL5 MCU Package, modify, compile and debug or run it. For further information, you can refer to AN5394 and AN5424 application notes.ECOPACK 2: New grade to identify brominated chlorinated and antimony oxide flame retardant free products.Please contact our sales support Limited Engineering samples available Preview: My personal data will be provided to ST affiliates and distributors of ST in countries located in the European Union and outside of the European Union for the same marketing purposes Read more I can also exercise other user’s rights at any time as described in the Privacy Policy. ST uses the personal data that you provide directly to it and through your activity on ST websites in accordance with the Privacy Policy, to send you (directly or via ST local affiliates or distributors) newsletters, advertisements or other specific and targeted marketing material about ST products and services. Your personal data will be provided to ST local affiliates and distributors in countries located in the European Union and outside of the European Union. You can consult the list of ST local affiliates and distributors in our website’s Privacy Policy.This link will be valid for 24 hours. Please check your spam filters in case you did not receive the email. Consider that modern browsers: It's easy and takes only 1 minute. It's easy and takes only 1 minute. It's easy and takes only 1 minute.

Click here to go back In case you did not receive any code please select 'I did not receive code' It's easy and takes only 1 minute. My personal data will be provided to ST affiliates and distributors of ST in countries located in the European Union and outside of the European Union for the same marketing purposes I can also exercise other user’s rights at any time as described in the Privacy Policy. ST uses the personal data that you provide directly to it and through your activity on ST websites in accordance with the Privacy Policy, to send you (directly or via ST local affiliates or distributors) newsletters, advertisements or other specific and targeted marketing material about ST products and services. You can consult the list of ST local affiliates and distributors in our website’s Privacy Policy.Please try again. Please enable Javascript to run in your browser and reload this page. You can also download your user manual here. This is shown on the service sticker of your Whirlpool appliance e.g. WWDC 9444. You can also search using the 12 digit number on the service sticker (this usually start with 85.). Remove one before adding a new item. You will not be not longer able to display your past transactions. The products described above, corresponding to this, bear the CE-mark. Failure to read, understand and follow the instructions may result in personal injury. Always keep it handy for reference. The device should only be operated by laboratory personnel especially trained for this purpose and familiar with all precautionary measures required for working in a laboratory. To avoid injuries and damage observe the safety instructions of the operating manual. WARNING Failure to observe the safety instructions. Serious injuries and unit damage. ? Observe the safety instructions in this operating manual. ? Carefully read the complete operating instructions of the refrigerated incubator KB. 1.

1 Legal considerations This operating manual is for informational purposes only. It contains information for installing, start-up, operation and maintenance of the product. Note: the contents and the product described are subject to change without notice. Understanding and observing the instructions in this operating manual are prerequisites for hazard-free use and safety during operation and maintenance. In no event shall BINDER be held liable for any damages, direct or incidental arising out of or related to the use of this manual. This operating manual cannot cover all conceivable applications. If you would like additional information, or if special problems arise that are not sufficiently addressed in this manual, please ask your dealer or contact us directly by phone at the number located on page one of this manual Furthermore, we emphasize that the contents of this operating manual are not part of an earlier or existing agreement, description, or legal relationship, nor do they modify such a relationship. All obligations on the part of BINDER derive from the respective purchase contract, which also contains the entire and exclusively valid statement of warranty administration. The statements in this manual neither augment nor restrict the contractual warranty provisions. 1.2 Structure of the safety instructions In this operating manual, the following safety definitions and symbols indicate dangerous situations following the harmonization of ISO 3864-2 and ANSI Z535.6. 1.2.1 Signal word panel Depending on the probability of serious consequences, potential dangers are identified with a signal word, the corresponding safety color, and if appropriate, the safety alert symbol. DANGER Indicates an imminently hazardous situation that, if not avoided, will result in death or serious (irreversible) injury. Possible consequences. ? Instruction how to avoid the hazard: prohibition. Replace safety labels that are no longer legible.

BINDER GmbH is only responsible for the safety features of the unit provided skilled electricians or qualified personnel authorized by BINDER perform all maintenance and repair, and if components relating to chamber safety are replaced in the event of failure with original spare parts. To operate the unit, use only original BINDER accessories or accessories from third-party suppliers authorized by BINDER. The user is responsible for any risk caused by using unauthorized accessories. CAUTION Danger of overheating. Damage to the unit. ? Do NOT install the unit in unventilated recesses. ? Ensure sufficient ventilation for dispersal of the heat. Do not operate the refrigerated incubator KB in hazardous locations. DANGER Explosion hazard. Danger of death. ? Do NOT operate the unit in potentially explosive areas. ? KEEP explosive dust or air-solvent mixtures AWAY from the unit. The refrigerated incubator KB does not dispose of any measures of explosion protection. Danger of death. ? Do NOT introduce any substance into the refrigerated incubator which is combustible or explosive at working temperature. ? NO explosive dust or air-solvent mixture in the inner chamber. Any solvent contained in the charging material must not be explosive or inflammable. I.e., irrespective of the solvent concentration in the steam room, NO explosive mixture with air must form. The temperature inside the chamber must lie below the flash point or below the sublimation point of the charging material. Familiarize yourself with the physical and chemical properties of the charging material, as well as the contained moisture constituent and its behavior with the addition of heat energy. Familiarize yourself with any potential health risks caused by the charging material, the contained moisture constituent or by reaction products which may arise during the temperature process. Take adequate measures to exclude such risks prior to putting the refrigerated incubator into operation.

DANGER Electrical hazard. CAUTION The glass doors and the inner chamber will become hot during operation. Danger of burning. ? Do NOT touch the glass doors, the inner surfaces or the charging material during operation. WARNING Stability hazard. Danger of injury. Damage to the unit and the charging material. Housing cover breakaway. ? Do NOT climb on the lower housing cover. ? Do NOT load the lower housing cover with heavy objects while the unit door is open. 1.6 Intended use Refrigerated incubators KB are suitable for exact conditioning of harmless materials. The operating temperature must lie below the flash point or below the sublimation point of the charging material. Following the instructions in this operating manual and conducting regular maintenance work (chap. 17.1) are part of the intended use. The charging material shall not contain any corrosive ingredients that may damage the machine components made of stainless steel, aluminum, and copper. Such ingredients include in particular acids and halides. Any corrosive damage caused by such ingredients is excluded from liability by BINDER GmbH. It fulfills all technical and application-specific requirements arising in experimentation such as in the areas of biotechnology, medicine, the nutrition industry, pharmaceutical and cosmetics industries, botany, and zoology. Two important temperature technologies have been combined to achieve perfect temperature control. The refrigerating system is distinguished by direct, precise, and rapid temperature conduction. The inner glass door ensures that the temperature remains constant when observing the incubation process. The air turbine supports exact attainment and maintenance of the desired temperature accuracy. The fan speed is digitally adjustable. The heating and refrigerating systems are microprocessor regulated to a tenth of a degree.

In addition, the refrigerated incubator provides almost unlimited possibilities for adaptation to individual customer requirements based upon extensive programming options and on the week program timer and real time clock of the controller. All unit functions are easy and comfortable to use thanks to their clear arrangement. Major features are easy cleaning of all unit parts and avoidance of undesired contamination. The inner chamber, the pre-heating chamber and the interior side of the doors are all made of stainless steel (material no. 1.4301 (V2A) in Germany, US equivalent 304). The housing is RAL 7035 powdercoated. All corners and edges are also completely coated. Both front castors can be easily locked via the attached brakes. Inform the carrier immediately if transportation damage has occurred. The final tests of the manufacturer may have caused traces of the shelves on the inner surfaces. This has no impact on the function and performance of the unit. CAUTION Sliding or tilting of the unit. Damage to the unit. Risk of injury by lifting heavy loads. ? Do NOT lift or transport the unit using the door, the handle, or the lower housing. ? Do NOT lift units size 720 by hand. ? Lift units size 240 from the pallet with the aid of six people or with a fork lifter. Set the fork lifter only from the front or rear in the middle of the unit. ? Lift units size 720 using technical devices (fork lifter) from the pallet. Set the fork lifter only from the front or rear in the middle of the unit. ? Do NOT set the fork lifter from the unit side. If you need to return the unit, please use the original packing and observe the guidelines for safe lifting and transportation (chap. 3.2). For disposal of the transport packing, see chap. 18.1. Note on second-hand units (Ex-Demo-Units): Second-hand units are units that were used for a short time for tests or exhibitions. They are thoroughly tested before resale.

BINDER ensures that the chamber is technically sound and will work flawlessly. Second-hand units are marked with a sticker on the unit door. Please remove the sticker before commissioning the unit. 3.2 Guidelines for safe lifting and transportation The front castors can be blocked by brakes. Please move the units with castors only when empty and on an even surface, otherwise the castors may be damaged. Damage to the unit. Risk of injury by lifting heavy loads. ? Transport the unit in its original packaging only. ? For moving or shipping, secure the unit with transport straps. ? Do NOT lift or transport the unit using the door, the handle, or the lower housing. ? Do NOT lift units size 720 by hand. ? Lift units size 240 with the aid of 6 people or with a fork lifter. Set the fork lifter only from the front or rear in the middle of the unit. ? Lift units size 720 using technical devices (fork lifter). Before start-up, wait at least one hour until the chamber has attained ambient temperature and is completely dry. 3.4 Location of installation and ambient conditions Set up the refrigerated incubator KB on a flat, even surface, free from vibration, in a well-ventilated, dry location and align it using a spirit level. The site of installation must be capable of supporting the unit’s weight (see technical data, chap. 20.4). The chambers are designed for setting up inside a building (indoor use). CAUTION Danger by stacking. Damage to the units. ? Do NOT place the refrigerated incubators on top of each other. To completely separate the unit from the power supply, you must disconnect the power plug. Install the unit in a way that the power plug is easily accessible and can be easily pulled in case of danger. With an increased amount of dust in the ambient air, clean the condenser fan (by suction or blowing) several times a year. Avoid any conductive dust in the ambiance according to the unit layout complying with pollution degree 2 (IEC 61010-1).

Do not install or operate the unit in potentially explosive areas. DANGER Explosion hazard.Damage to the equipment. ? Check the power supply voltage before connection and start-up. ? Compare the power supply voltage with the data indicated on the type plate. See also electrical data (chap. 20.4). To completely separate the unit from the power supply, you must disconnect the power plug. Install the unit in a way that the power plug is easily accessible and can be easily pulled in case of danger. 4.2 Spacers for wall distance Please fix both spacers with the supplied screws at the unit rear. Warming chambers may release odors in the first few days after commissioning. This is not a quality defect. To reduce odors quickly we recommend heating up the chamber to its nominal temperature for one day and in a well-ventilated location. Depending on the temperature value entered before, LED (3a) is lit if the heating is active, or LED (3b) if the refrigeration is active, or no LED if the actual temperature is equal to the set-point. In program operation: program interruption. (3d) The program controller RD3 permits programming of temperature cycles. For each program section also the fan speed can be regulated. Two programs with up to 10 sections each or one program with up to 20 sections can be entered (setting in the user level, chap. 10). When changing from 2 programs to 1 program or vice-versa, existing programs are deleted The maximum length of an individual program section can be set to either 99 hs 59 min or to 999 hs 59 min (setting in the user level, chap. 10). This setting is then valid for all program sections.Any setting of the operation lines in Fixed value entry mode is ineffective with an active week program timer. Enter the values with the arrow keys. A value flashing once after 2 seconds indicates that it has been applied by the controller. When changing the set-point, check the safety controller setting in the user level (chap.

10) if the safety controller has been set to “limit” mode. If the fan is operated with less than 100 % speed, the temperature performance and the spatial exactitude of the temperature can differ from the manufacturer’s specifications. Do reduce the fan speed only if absolutely necessary due to special requirements. The values entered in fixed-value entry mode remain valid after program run-off and are then equilibrated. If the week program timer is active, depending on the running week program another set-point (SP2) may be targeted. Too high or too low temperatures can occur which exceed the permissible temperature of the charging material. Damage to the charging material. ? Deactivate the week program timer if you do not use it. 7. Week program editor The Week program editor permits defining up to 4 shift point for each week day. A shift point defines a moment and the switching state ON or OFF of the channels that become active in this instance. Therefore, you need to activate the week program timer in the user level (chap. 10). Normal Display Display 1 shows e.g. 19.8 Display 2 shows e.g. 15.05.06 13:52 - - (actual temperature value) (actual date and time, actual state of week program timer channel 1: Off, channel 2: Off) Press down key Display 1 shows Display 2 shows e.g. 0000 PROGRAM EDITOR Press down key Display 1 shows 0000 Display 2 shows WEEK PROG. EDITOR for 5 sec (you are in the program editor) for 5 sec Menu visible only if week program timer is activated in the user level (chap. 10) (you are in the week program editor) Press program key Display 1 shows 0000 Display 2 shows UserCod? 0000 Enter the user code using arrow keys (enter user code, display flashes) e.g. 0001 (basic setting, adjustable in the user level, chap. 10). Value is shown in both displays. In the user level (chap. 10) you can select between the settings “Ramp” (default setting) and “Step”. Setting “Ramp” permits programming all kinds of temperature transitions.

With setting “Step” the controller will equilibrate only to constant temperatures; programming ramps is no longer possible. Switching between settings “Ramp” and “Step” will influence all programs. Please note that this can cause the time courses of existing programs to change significantly. 8.1.1 Programming with setting “Ramp” (default setting) Set-points always refer to the start of a program section, i.e., at the beginning of each program section, the entered set-point will be reached. During program section operation, the temperature gradually passes to the set-point entered for the subsequent program section. Two program sections with an identical set-point are followed by a section with a different set-point. If the duration of this transitional program section is very short (minimum entry 1 min), the temperature change will proceed rapidly within the minimum amount of time. Otherwise, the program will stop one section too early because the program line is incomplete. 8.1.2 Programming with setting “step” With setting “Step” selected, you don’t need to program the transition section in the Program Editor. With setting “step” the controller will equilibrate only to constant temperatures; programming ramps is no longer possible. The set-points are maintained constant for the duration of a program section. At the start of each program section, the unit heats up with the maximum speed in order to attain the entered set-point. During this program interruption, the LED (3d) flashes. Therefore, the duration of the program might be extended due to the programming of tolerances Programming is saved even in case of a power failure or after turning off the unit. After program rundown the controller returns to Fixed value operation showing Normal Display and equilibrates to the temperature value previously entered in fixed value entry mode. Before starting the program, check the set-point value entered in Fixed value entry mode.

After program rundown temperature will equilibrate to this value. Then enter the set-points one after the other in all program sections of a selected program. Automatically forward after 2 sec. Example: If three programs sections have been already entered, the next section to be entered is S04. Enter the values of the individual parameters with the arrow keys. A value flashes once after 2 seconds thus indicating that it has been taken over to the controller. If no button is pressed for more than 120 sec the controller toggles back to Normal Display. The program entered to this point remains stored. If all sections up to S10 or up to S20 have been programmed, section S01 follows again. When changing the set-point, check the setting of the safety controller in the user level (chap. 10) if the safety controller has been set to “limit” mode. Normal display Press down key Display 1 shows Display 2 shows for 5 sec. e.g. 0000 PROGRAM EDITOR (you are in the program editor) Press program key Display 1 shows Display 2 shows 0000 UserCod? 0000 (enter user code) Enter the user code using arrow keys e.g. 0001 (basic setting, adjustable in the user level, chap. 10). Value is shown in both displays. In our example, section S03 has been deleted. If sections S04, S05, etc.Deletion leads to overwriting the section by the following one. It is therefore not possible to temporarily inactivate a program section. To enter a section later to a program, all the sections following the new one must be entered again. 9. Program start level Before starting the program, check the set-point entered in Fixed value operation mode. After end of the program, the temperature will equilibrate to this value. CAUTION Too high or too low temperature after the program ends. Damage to the charging material. ? Check the set-point of Fixed value operation and if necessary adapt it. After the program ends, the temperature will equilibrate to the set-point entered in Fixed value operation mode.